_ | |__ _____ ____ _ _ __ | '_ \ / _ \ \ /\ / / _` | '_ \ | |_) | __/\ V V / (_| | | | | |_.__/ \___| \_/\_/ \__,_|_| |_| Portions Copyright (c) 2005-2007 bewan systems www.bewan.com Parameters: Product : A50181 Product family : A50180 Flash size : 1000000 DRAM size : 2000000 Ethernet : RMII LAN MAC address : 00:0c:c3:71:07:bd WAN MAC address : 00:0c:c3:71:07:bd Dual bank boot : yes Reset : no Serial number : 990000074075492 WEP key : TA3HQGWL3PMHH Loader version : 5304 Found valid bootable partition 0: Copyright (c) 2006 BeWAN Systems BeWAN iBox rev2 Annex A - Saunalahti A50181 2007-05-14-12:05:14 A50181-sauna10-5771.bin Found valid bootable partition 1: Copyright (c) 2006-2008 BeWAN Systems BeWAN iBox rev2 Annex A - Saunalahti A50181 2008-04-23-17:32:23 A50181-Sauna27-11988.bin Booting from partition 1 in flash. Loading: Linux Kernel Image Load address = 80000000 Uncompressing Linux.................... done, booting the kernel. start addr = 802AD000 LINUX started... LINUX command line: nofpu console=ttyS0,115200n1 bewan_boot=flash1 bewan_fs_addr=0x8ee000 bewan_fs_size=0x667000 mem=30M memsize not set in boot prom, set to default (16Mb) Linux version 2.6.16bewan (build@bewan.com) (gcc version 3.3.4) #1 CPU revision is: 0001800a pcibios_init: Determined physical RAM map: memory: 00001000 @ 00000000 (reserved) memory: 0000f000 @ 00001000 (ROM data) memory: 000f0000 @ 00010000 (usable) memory: 001f1000 @ 00100000 (reserved) memory: 00d0f000 @ 002f1000 (usable) User-defined physical RAM map: memory: 01e00000 @ 00000000 (usable) Built 1 zonelists Kernel command line: nofpu console=ttyS0,115200n1 bewan_boot=flash1 bewan_fs_addr=0x8ee000 bewan_fs_size=0x667000 mem=30M Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes. Primary data cache 8kB, 2-way, linesize 16 bytes. Synthesized TLB refill handler (21 instructions). Synthesized TLB load handler fastpath (33 instructions). Synthesized TLB store handler fastpath (33 instructions). Synthesized TLB modify handler fastpath (32 instructions). PID hash table entries: 128 (order: 7, 2048 bytes) CPU frequency 197.84 MHz Using 98.918 MHz high precision timer. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 27436k/30720k available (2280k kernel code, 3284k reserved, 455k data, 148k init, 0k highmem) Mount-cache hash table entries: 512 Checking for 'wait' instruction... available. NET: Registered protocol family 16 Enabling device PCI: Enabling device 0000:00:00.0 (0000 -> 0003) TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca) squashfs: version 3.0 (2006/03/15) Phillip Lougher Squashfs 2.2 with LZMA support devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 Initializing Cryptographic API io scheduler noop registered (default) Serial: 8250/16550 driver $Revision: 1.1 $ 5 ports, IRQ sharing disabled ttyS0: autoconf (0xa6340000, 0xa6340000): type=16550A serial8250: ttyS0 at MMIO 0x0 (irq = 0) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize loop: loaded (max 8 devices) PPP generic driver version 2.4.2 NET: Registered protocol family 24 Centillium IAD flash device: 0x1000000 at 0xad000000 Centillium IAD FLASH: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 Centillium IAD FLASH: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Creating 5 MTD partitions on "Centillium IAD FLASH": 0x00000000-0x01000000 : "Flash" 0x00000000-0x00020000 : "Loader" 0x00020000-0x00040000 : "Config" 0x00820000-0x01000000 : "Firmware" 0x00040000-0x00820000 : "OldFirmware" Creating 1 MTD partitions on "Centillium IAD FLASH": 0x008ee000-0x00f55000 : "romFS" GACT probability on Mirror/redirect action on netem: version 1.2 u32 classifier Perfomance counters on input device check on Actions configured Netfilter messages via NETLINK v0.30. NET: Registered protocol family 2 IP route cache hash table entries: 256 (order: -2, 1024 bytes) TCP established hash table entries: 1024 (order: 0, 4096 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered ip_conntrack version 2.4 (240 buckets, 1920 max) - 232 bytes per conntrack ctnetlink v0.90: registering with nfnetlink. ip_tables: (C) 2000-2006 Netfilter Core Team arp_tables: (C) 2002 David S. Miller TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller Ethernet Multiplexer Support v1.0 Christophe Piel (c) 2006 BeWAN systems VFS: Mounted root (squashfs filesystem) readonly. Mounted devfs on /dev Freeing prom memory: 0kb freed Freeing unused kernel memory: 148k freed init started: BusyBox v1.00 multi-call binary Starting pid 111, console /dev/tts/0: '/etc/rc' Algorithmics/MIPS FPU Emulator v1.5 Software Watchdog Timer: 0.05, timer margin: 120 sec. Mon Jan 1 00:00:00 UTC 2007 LED and Buttons driver: v2.6.0 _ | |__ _____ ____ _ _ __ | '_ \ / _ \ \ /\ / / _` | '_ \ | |_) | __/\ V V / (_| | | | | |_.__/ \___| \_/\_/ \__,_|_| |_| EXT2-fs warning: mounting fs with errors, running e2fsck is recommended EXT2-fs error (device ram0): ext2_check_page: bad entry in directory #2: unaligned directory entry - offset=0, inode=4294967295, rec_len=65535, name_len=255 No config file Restoring default configuration ctlmapi: module license 'unspecified' taints kernel. BuildSpec: wlanc3v_voipc3a_rel Date: 2008-04-23 Time: 17:32 Version: Linux 1.4B Lib Version: B5.1 DSP_SPEC: 3Av165_14_2B_Av225_0203 Firmware Version:b3fb:ef00 Flash Type :PARALLEL MIPS Device Type:IAD_CHIRON3_P400 Host/DSP Clock :197MHz iadinfo: Module loaded. enter start device G.dmt.bis Annex A Modem Configuration [SUCCESS] Enabling eXtremeDSL operation [SUCCESS] DS max rate = 0 kbps US max rate = 0 kbps DS payload rate = 0 kbps US payload rate = 0 kbps Local CRC = 0 Remote CRC = 0 eth0: set TX mode to Half Duplex eth0: set MII clock to 10MB eth1: set TX mode to Half Duplex eth1: set MII clock to 10MB ctlm_tel: daa 1 slic 2 country FI usbcore: registered new driver usbfs usbcore: registered new driver hub SCSI subsystem initialized Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. PCI: Enabling device 0000:00:06.2 (0000 -> 0002) ehci_hcd 0000:00:06.2: EHCI Host Controller ehci_hcd 0000:00:06.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:06.2: irq 9, io mem 0xa9810000 ehci_hcd 0000:00:06.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected USB Universal Host Controller Interface driver v2.3 PCI: Enabling device 0000:00:06.0 (0000 -> 0001) uhci_hcd 0000:00:06.0: UHCI Host Controller uhci_hcd 0000:00:06.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:06.0: irq 9, io base 0xabf10000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected PCI: Enabling device 0000:00:06.1 (0000 -> 0001) uhci_hcd 0000:00:06.1: UHCI Host Controller uhci_hcd 0000:00:06.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:06.1: irq 9, io base 0xabf10020 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected Linux video capture interface: v1.00 pwc: Philips webcam module version 10.0.12-rc1 loaded. pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840. pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30, pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100. usbcore: registered new driver Philips webcam usbcore: registered new driver quickcam usbcore: registered new driver gspca ../user/gspca/gspca_core.c: gspca driver 01.00.18 registered build router.conf from factory /etc/init.d/syslog start /etc/eom.d/update-config /etc/init.d/dsl start /etc/init.d/interface start LANEthernetInterface 1 /etc/init.d/switch nothing 1 /etc/init.d/phy stop 1 1 using the specified MII index 1. power down... /etc/init.d/switchvlan nothing 1 /etc/init.d/interface start LANEthernetInterface 2 /etc/init.d/switch nothing 2 /etc/init.d/phy stop 2 1 using the specified MII index 2. power down... eth0: set TX mode to Half Duplex eth0: set MII clock to 100MB eth1: set TX mode to Half Duplex eth1: set MII clock to 100MB /etc/init.d/switchvlan nothing 2 /etc/init.d/interface start LANUSBInterface 1 wireless config : atheros /etc/init.d/wifi.d/wifi start 1 ath_hal: 0.9.17.1 (AR5212, RF5111, RF5112, RF2413, RF5413) ath_dfs: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved wlan: 0.8.4.2 (Atheros/multi-bss) ath_rate_atheros: Version 2.0.1 Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved ath_pci: 0.9.4.5 (Atheros/multi-bss) PCI: Enabling device 0000:00:05.0 (0000 -> 0002) wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: mac 7.8 phy 4.5 radio 5.6 wifi0: Use hw queue 1 for WME_AC_BE traffic wifi0: Use hw queue 0 for WME_AC_BK traffic wifi0: Use hw queue 2 for WME_AC_VI traffic wifi0: Use hw queue 3 for WME_AC_VO traffic wifi0: Use hw queue 8 for CAB traffic wifi0: Use hw queue 9 for beacons wifi0: Atheros 5212: mem=0xa9800000, irq=11 /etc/init.d/wifi.d/easyp nothing /etc/init.d/wifi.d/wifi start 2 /etc/init.d/wifi.d/easyp nothing /etc/init.d/wifi.d/wifi start 3 /etc/init.d/wifi.d/easyp nothing /etc/init.d/interface nothing ATMEthernetInterface 1 /etc/init.d/interface start ATMEthernetInterface 2 /etc/init.d/atm start 2 /bin/atmcfg atm2 -flowset 0 0 0 3 0 0 0 1 /bin/atmcfg atm2 -vccopen 0 100 0 llc brip atm_vcc_open: ATM vcc (0/100) open succeesful. /etc/init.d/interface start ATMEthernetInterface 3 /etc/init.d/atm start 3 /bin/atmcfg atm3 -flowset 1 0 0 3 0 0 0 1 /bin/atmcfg atm3 -vccopen 0 33 1 llc brip atm_vcc_open: ATM vcc (0/33) open succeesful. /etc/init.d/interface start ATMEthernetInterface 4 /etc/init.d/atm start 4 /bin/atmcfg atm4 -flowset 2 0 0 3 0 0 0 1 /bin/atmcfg atm4 -vccopen 14 24 2 llc brip atm_vcc_open: ATM vcc (14/24) open succeesful. /etc/init.d/interface start ATMEthernetInterface 5 /etc/init.d/atm start 5 /bin/atmcfg atm5 -flowset 3 0 0 3 0 0 0 1 /bin/atmcfg atm5 -vccopen 8 35 3 llc brip atm_vcc_open: ATM vcc (8/35) open succeesful. /etc/init.d/autodslam start auto-stop /etc/init.d/lan start 1 /etc/init.d/lanif start 1 all /etc/init.d/lanintf start lan1 eth0 device eth0 entered promiscuous mode /etc/init.d/lanintf start lan1 eth1 device eth1 entered promiscuous mode /etc/init.d/lanintf start lan1 usb0 device usb0 entered promiscuous mode /etc/init.d/lanintf start lan1 ath0 device ath0 entered promiscuous mode /etc/init.d/shaping nothing /etc/init.d/lanip start 1 /etc/config.default/ip-up-dhcp lan1 192.168.0.1 lan1: port 4(ath0) entering listening state lan1: port 3(usb0) entering listening state lan1: port 2(eth1) entering listening state lan1: port 1(eth0) entering listening state /etc/init.d/host start /etc/init.d/igmp start /etc/init.d/inittab /etc/init.d/ipsec restart all /etc/init.d/ipsec start 1 /etc/init.d/landhcp start 1 /etc/init.d/wifi.d/lanacl start 1 /etc/init.d/passthrough start 1 /etc/init.d/racoon stop /etc/init.d/lan start 2 /etc/init.d/lanif start 2 all /etc/init.d/lanintf start lan2 ath1 device ath1 entered promiscuous mode /etc/init.d/shaping nothing /etc/init.d/lanip start 2 /etc/config.default/ip-up-dhcp lan2 192.168.1.1 lan2: port 1(ath1) entering learning state /etc/init.d/host start /etc/init.d/igmp start /etc/init.d/inittab lan1: port 4(ath0) entering learning state lan1: port 3(usb0) entering learning state lan1: port 2(eth1) entering learning state lan1: port 1(eth0) entering learning state /etc/init.d/ipsec restart all /etc/init.d/ipsec start 1 /etc/init.d/landhcp start 2 /etc/init.d/wifi.d/lanacl start 2 /etc/init.d/passthrough nothing 2 /etc/init.d/lan start 3 /etc/init.d/racoon stop /etc/init.d/lanif start 3 all /etc/init.d/lanintf start lan3 ath2 device ath2 entered promiscuous mode /etc/init.d/shaping nothing /etc/init.d/lanip start 3 /etc/config.default/ip-up-dhcp lan3 10.0.1.17 lan3: port 1(ath2) entering learning state /etc/init.d/host start /etc/init.d/igmp start /etc/init.d/inittab /etc/init.d/ipsec restart all /etc/init.d/landhcp start 3 lan2: topology change detected, propagating lan2: port 1(ath1) entering forwarding state /etc/init.d/ipsec start 1 /etc/init.d/wifi.d/lanacl start 3 /etc/init.d/passthrough nothing 3 /etc/init.d/lan nothing 4 /etc/init.d/users start /etc/init.d/racoon stop /etc/init.d/unix start /etc/init.d/unixusers start 1 lan1: topology change detected, propagating lan1: port 4(ath0) entering forwarding state lan1: topology change detected, propagating lan1: port 3(usb0) entering forwarding state lan1: topology change detected, propagating lan1: port 2(eth1) entering forwarding state lan1: topology change detected, propagating lan1: port 1(eth0) entering forwarding state /etc/init.d/unixusers start 2 /etc/init.d/samba start /etc/init.d/pureftpd start /etc/init.d/unixadmin start /etc/init.d/time start /etc/init.d/mdns nothing /etc/init.d/rmthttp start /etc/init.d/wan start 1 device atm2 entered promiscuous mode device atm3 entered promiscuous mode device atm4 entered promiscuous mode device atm5 entered promiscuous mode /etc/init.d/interface start WANConnectionDevice 1 SIOCSIFHWADDR: Cannot assign wan1: port 4(atm5) entering learning state requested addreswan1: port 3(atm4) entering learning state s wan1: port 2(atm3) entering learning state wan1: port 1(atm2) entering learning state /etc/init.d/wannet start 1 /etc/init.d/wanbr nothing 1 /etc/init.d/wanip start 1 lan3: topology change detected, propagating lan3: port 1(ath2) entering forwarding state /etc/init.d/wanppp nothing 1 /etc/init.d/firewall start 1 /etc/init.d/ports start 1 /etc/init.d/wan nothing 2 /etc/init.d/wan nothing 3 /etc/init.d/wan nothing 4 /etc/init.d/qos start all /etc/init.d/shaping nothing /etc/init.d/dhcp start all /etc/init.d/dhcpd nothing all /etc/init.d/dhcrelay nothing all /etc/init.d/hbrdhcp start all /etc/init.d/dnsmasq start all /etc/init.d/dnsmasq start all /etc/init.d/pppd start all /etc/init.d/dhclient start all /etc/init.d/wifi.d/hostapd start all /etc/init.d/wifi.d/wpa_supplicant start all /etc/init.d/pptp stop /etc/init.d/openl2tp stop /etc/init.d/ipsec all /etc/init.d/fwrules start /etc/init.d/iptables start /etc/init.d/ebtables start /etc/init.d/ebtables: 316: ebtables: not found /etc/init.d/ebtables: 316: ebtables: not found /etc/init.d/ebtables: 316: ebtables: not found /etc/init.d/ebtables: 316: ebtables: not found /etc/init.d/ebtables: 1: ebtables: not found /etc/init.d/ebtables: 1: ebtables: not found /etc/init.d/ebtables: 1: ebtables: not found /etc/init.d/ebtables: 1: ebtables: not found /etc/init.d/routes start /etc/init.d/upnp start /etc/init.d/dyndns nothing /etc/init.d/inittab /etc/init.d/stunnel start /etc/init.d/phy start 1 1 using the specified MII index 1. resetting the transceiver... restarting autonegotiation... /etc/init.d/phy start 2 1 using the specified MII index 2. resetting the transceiver... restarting autonegotiation... /etc/init.d/inittab rc completed Starting pid 1580, console /dev/null: '/sbin/klogd' Starting pid 1579, console /dev/null: '/sbin/syslogd' eth0: set TX mode to Half Duplex eth0: set MII clock to 10MB eth1: set TX mode to Half Duplex eth1: set MII clock to 10MB Starting pid 1581, console /dev/null: '/bin/dhclient' Starting pid 1587, console /dev/console: '/bin/wdgd' Software Watchdog Timer: set margin to 40 sec. Starting pid 1582, console /dev/null: '/bin/dnsmasq-2' Starting pid 1583, console /dev/null: '/sbin/hostapd' Starting pid 1584, console /dev/null: '/sbin/igmpproxyd' Starting pid 1585, console /dev/console: '/bin/resetd' lan2: port 1(ath1) entering disabled state Starting pid 1586, console /dev/null: '/bin/upnpd' lan2: port 1(ath1) entering learning state wan1: topology change detected, propagating wan1: port 4(atm5) entering forwarding state wan1: topology change detected, propagating wan1: port 3(atm4) entering forwarding state wan1: topology change detected, propagating wan1: port 2(atm3) entering forwarding state wan1: topology change detected, propagating wan1: port 1(atm2) entering forwarding state /etc/init.d/upgd nothing /etc/init.d/inetd start /etc/init.d/http start /etc/init.d/htpwd start /etc/init.d/tr069 start /etc/init.d/usbdevices usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for airprime usbcore: registered new driver airprime /etc/init.d/voip-asterisk nothing /etc/init.d/bluetooth nothing /etc/init.d/host start lan2: topology change detected, propagating lan2: port 1(ath1) entering forwarding state /etc/init.d/userscreatedir start /etc/init.d/usersdir start 1 /etc/init.d/usersdir start 2 /etc/init.d/sambaserver refresh /etc/init.d/upnpav nothing /etc/init.d/pureftpdserver start /etc/init.d/obexpush nothing4 /etc/init.d/web nothing /etc/init.d/printer start /etc/init.d/webcam start usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver /etc/init.d/inittab Reloading /etc/inittab Starting pid 1821, console /dev/console: '/bin/thttpd' Starting pid 1823, console /dev/null: '/bin/lighttpd' Starting pid 1822, console /dev/console: '/bin/tr069'